Chimney Repair in Hollywood - You See the Footage Before You Get a Price

Trusted Chimney Repair for Hollywood Homeowners

A cracked crown, a rusted cap, or a flue that’s pulling poorly is the kind of problem that gets worse quietly. In Hollywood’s wet summers and warm, humid air, water finds every gap in masonry and metal, and a small flashing leak can rot framing before anyone notices. Chimney repair in Hollywood, FL is what we do: we sweep, inspect, and repair, all three under one company, so nobody hands your chimney to a second crew. Our technicians have up to 8 years of experience and work with proven product lines like HeatShield and Gelco rather than generic substitutes. We document every inspection in writing, which matters at insurance renewal and at closing. We answer 24/7, and fast dispatch runs from 7am to 7pm Sunday through Friday. Call (833) 974-6567 for a free estimate.

Call (833) 974-6567

Chimney Cap Installation

Chimney cap installation is the fitting of a screened metal or stainless cap over the flue opening, and it’s the single most effective thing you can do to keep rain and animals out of a chimney. If your flue is open to the sky, you need one – open flues take in water every storm, and birds, squirrels, and raccoons treat an uncapped chimney as a den. We install Gelco and Famco caps, sized and sealed to the flue rather than wedged on, because a cap that lifts in wind lets in exactly what it was meant to stop. A typical cap installation runs $250-$650 depending on flue count, cap style, and how much sealing the crown needs.

Stainless Caps and Animal Screens

Stainless steel caps hold up far better than painted galvanized in humid air, and a proper animal screen uses a mesh tight enough to stop squirrels while staying easy to brush through at sweep time. We match the cap to the flue size so the screen sits flush and the lid can’t be pried up by wind.

Multi-Flue and Custom Fits

A chimney with two flues needs either two caps or one custom lid with a shared screen box, and getting this wrong usually shows up as a lid that rattles or a gap at the edge of the crown. We measure on site and set the cap level so water runs off rather than pooling at the base.

Chimney Cap Replacement

Chimney cap replacement is the removal of a failed cap and the fitting of a new one, and the signs that it’s time are fairly plain: rust perforation, a bent or missing lid, torn screening, or water stains on the smoke chamber after a heavy rain. Caps rust from the inside out in this climate, so a cap that looks solid from the driveway can already have pinholes at the seams. We inspect the cap as part of every sweep and tell you plainly whether it has another few years or needs to go now. We also check that whatever killed the old cap (poor sealing, a loose crown, a too-small flue) is corrected, because a new cap on the same bad seal will fail the same way. Replacement typically runs $250-$650 including the new Gelco or Famco unit and the sealing.

Spotting Rust and Loose Seals

Run a hand along the cap edge and look for flaking paint or rust bleed at the seams; that’s usually the first failure point. A cap that rocks when you nudge it from below has lost its fastening or seal and should be reset before the next storm season.

When a Cap Can Be Reused

If the stainless and screening are sound and only the seal has failed, we can often reseat the existing cap and reflash the base rather than sell you a new one. We’ll say so when it’s true.

Chimney Liner Installation

Chimney liner installation is the fitting of a new flue lining inside the old chimney, and it’s needed when the existing clay tile is cracked, spalling, or missing, or when a new appliance needs a correctly sized flue. Cracks in a clay liner let heat and gases reach framing; that’s a safety issue, not a maintenance item, and a professional should assess it before you burn again. We work with DuraFlex flexible liner systems, which can be routed through offset and irregular flues that rigid sections can’t follow, and with HeatShield ceramic resurfacing, which can restore a damaged flue without a full reline. That’s the honest question we answer first: HeatShield resurfacing can save you the cost of a full reline, and we’ll tell you which one you actually need once we’ve seen the flue on camera. Liner work typically runs $1,800-$4,500 depending on liner length, diameter, and insulation. Everything is recommended only against camera evidence you can see yourself.

Flexible Liners for Offset Flues

Older Hollywood homes often have flues that jog around framing, and rigid pipe simply won’t make the turn. DuraFlex flexible liner navigates those bends with a continuous run, which also means fewer joints where creosote and moisture collect.

Resurfacing Instead of Relining

HeatShield applies a ceramic coating that bonds to the flue wall and fills the kind of cracking and pitting that would otherwise call for a full liner. It’s not right for every flue, but when it is, it’s a real saving and we’ll show you the before-and-after.

Chimney Flashing Repair

Chimney flashing repair covers the metal where the chimney meets the roof, and it’s the most common source of the water damage we find in Hollywood homes. Flashing is a layered system of step flashing, counterflashing, and sealant, and when any layer fails, water tracks down the chimney chase and shows up as a ceiling stain far from the actual leak. If you’ve seen damp patches after a hard rain, warped trim near the chimney, or rust streaks on the masonry, flashing is the first thing we check. We open the joints, replace failed metal rather than smearing sealant over it, and reflash the chimney so water sheds where it should. Flashing repair typically runs $400-$900 depending on roof pitch, chimney size, and how much metal has to be replaced. It’s often the cheapest repair on this page and the costliest to skip.

Water Stains and Their Meaning

A brown ring on the ceiling near the chimney is water that has traveled down the chase, and its location rarely points to the actual leak. We trace it from above with the roof opened up at the flashing rather than guessing from inside.

Sealing Versus Rebuilding

A failed sealant bead can sometimes be cut out and redone, but rusted or lifted metal has to be replaced. We look at the metal itself before deciding which one your flashing needs.

Chimney Crown Repair

Chimney crown repair addresses the concrete cap on top of the chimney, the sloped surface that sheds water away from the flue. A cracked or pitted crown lets water into the masonry below, and in a climate with heavy summer rain that water works its way down through the brick and shows up as efflorescence, spalling, or a damp smoke chamber. If the crown has visible cracks, a crumbled edge, or a slope that’s flattened out, it needs attention before the masonry underneath takes on damage. We rebuild failed crowns with a proper slope and overhang so water runs off the edge rather than sitting against the flue, and we seal around the flue base where most crowns fail first. Crown repair typically runs $450-$1,200 depending on crown size, access, and whether we’re rebuilding or resurfacing. A crown is a modest repair that protects a very expensive chimney.

Slope, Overhang, and Drainage

A proper crown slopes away from the flue and overhangs the brick slightly, so runoff clears the wall instead of running down it. Rebuilding to those lines is what keeps the repair from failing again in two years.

Hairline Cracks Versus Structural Failures

Fine surface checking can often be sealed and monitored, but a crack wide enough to catch a fingernail or a crown that has separated from the flue needs rebuilding. We’ll tell you which you’re looking at.

Chimney Repair Companies

Chimney repair companies vary widely in what they actually do in-house, and that difference matters when a job moves from sweeping to repair. Some firms sweep and then refer the repair out; others are general handymen with a brush and a ladder. We handle the full cycle: sweep, structural repair, and inspection, done by the same company so there’s no handoff and no second appointment with a different crew. If you’re comparing chimney repair companies in Hollywood, ask what product lines the firm actually installs. We name the brands we use – DuraFlex, HeatShield, Gelco, Famco, Olympia Chimney, and Copperfield – because the materials matter as much as the labor. Repair pricing depends entirely on the scope: a single cap or flashing job runs a few hundred dollars, while liner and masonry work moves into four figures. We give you a written estimate before any work begins, and the written estimate sets the final price.

What to Ask Before You Book

Ask whether the company performs repairs itself or subcontracts them, and which liner and cap brands it installs. A firm that can’t name its materials is usually installing whatever the supplier had on hand.

Written Reports and Documentation

We document every inspection in writing with photos, which is useful for insurance, real-estate disclosure, and warranty purposes. Ask any company you hire whether you’ll get that in writing.

Chimney Masonry Repair

Chimney masonry repair is the rebuilding or repointing of the brickwork and mortar joints that make up the chimney structure, and it’s needed when joints have eroded, bricks have spalled, or the chimney has begun to lean or separate from the house. Water is almost always the culprit: it gets in through a failed crown or flashing, soaks the brick, and then pushes the face off in freeze-free but still damaging wet-and-dry cycles. Left alone, spalling brick and soft mortar let the chimney move, and a chimney that has pulled away from the roofline is a structural concern that should be assessed promptly by a professional. We repoint eroded joints with mortar matched to the existing brick, replace spalled units, and correct the water path above so the repair holds. Masonry repair typically runs $600-$2,500 depending on the height of the chimney, the number of courses affected, and whether the repair is repointing or partial rebuild.

Repointing Versus Rebuilding

Repointing cuts out the failed mortar and packs fresh mortar into the joints, which restores the wall without disturbing sound brick. Rebuilding is reserved for sections where the brick itself has failed and can’t be saved.

Reading Efflorescence and Spalling

A white chalky bloom on the brick is salt pushed out by moisture passing through, and it’s an early warning that water is getting in above. Spalling, where the brick face flakes off, is the later stage and calls for repair rather than cleaning.

Brands We Service

We work with a defined set of professional product lines because the quality of the material is what determines whether a repair lasts. DuraFlex flexible liner systems are our answer for offset and irregular flues, where a continuous flexible run beats rigid sections that need joints at every turn. HeatShield ceramic resurfacing lets us restore a damaged flue without a full reline, which saves real money when the flue qualifies. Gelco and Famco are the two cap and cover brands we install, and they solve the moisture and animal problem that drives most of the damage we see in Hollywood chimneys.

We also draw on Olympia Chimney and Copperfield product lines, the kind of professional supplies that generalist outfits rarely stock or know how to install correctly. Our technicians have up to 8 years of experience with these systems, and we specify the brand and the reason in writing before any work starts. Whether you have DuraFlex, HeatShield, Gelco, Famco, Olympia Chimney, or Copperfield on your chimney, or any other make, we can help.

Signs You Need a Pro Right Now

• Water stains on the ceiling or smoke chamber. A brown ring after heavy rain means water is getting past the flashing, crown, or cap. Water damage spreads through framing quickly in this climate, so it’s worth a look before the next storm.
• A rusted or missing chimney cap. An open or failed cap lets in rain and animals, and the damage happens silently. A cap repair is inexpensive compared with what water does once it’s inside the chase.
• Cracked or flaking liner, or spalled brick in the smoke chamber. These let heat and gases reach places they shouldn’t. Have it assessed by a trained professional before you light another fire.
• A chimney that has pulled away from the roofline or is leaning. A gap at the joint is a structural warning. It needs an assessment rather than a wait-and-see approach.
• Poor draft, smoke spilling into the room, or a strong creosote smell. These often point to a blocked or damaged flue and call for an inspection with a camera before anything else.

Our Process, Step by Step

1. 1
   Sweep first. We clean the flue and firebox before inspecting, because a sooted flue hides the cracks and gaps that matter. That’s also when we check the cap and crown from above.
2. 2
   Inspect with a camera. We run a camera down the flue and photograph every stage, so we can show you the condition of the liner, smoke chamber, and joints rather than just tell you about it.
3. 3
   Explain what we found. We go through the photos with you and separate what needs fixing now from what can safely wait. Nothing is recommended without camera evidence you can see yourself.
4. 4
   Give a written estimate. You get a flat-price estimate with the scope and the product line named, and the written estimate sets the final price. No work begins until you approve it.
5. 5
   Do the repair and document it. The same company and crew handle the repair, and you get written documentation of the work for insurance, disclosure, or warranty purposes.

How Much Does Chimney Repair Cost in Hollywood?

Our Service Area Near Hollywood

We serve homeowners across Hollywood and the surrounding communities, including Dania Beach, Hallandale Beach, West Park, Ives Estates, Aventura, Ojus, Sunny Isles Beach, North Miami Beach, and Golden Glades. Response is scheduled around access and weather, and most jobs in these areas are booked promptly. For chimney repair in Dania Beach or the neighboring towns, we handle the full sweep-inspect-repair cycle under one company, and our chimney sweep service is the usual starting point when you’re not sure what condition the chimney is in. If you’re comparing options for chimney repair or chimney repair nearby, the estimate process is the same. Call to schedule.

Frequently Asked Questions About Chimney Repair in Hollywood

Schedule Your Chimney Repair Service in Hollywood Today

If your chimney has a cracked cap, a damp crown, or a flue you’re not sure about, don’t wait for burning season. We sweep, inspect, and repair under one company, document every inspection in writing, and tell you honestly when work can safely wait. Call (833) 974-6567. We answer 24/7. Fast dispatch, 7am-7pm, Sunday through Friday. Estimates are free and carry no obligation. Chimney repair in Hollywood starts with a phone call.

Written by the team at Chimney Sweep Hollywood.